Crossword Solver > found answer > UBENDS

Welcome to Anagrammer Crossword Genius! Keep reading below to see if ubends is an answer to any crossword puzzle or word game (Scrabble, Words With Friends etc). Scroll down to see all the info we have compiled on ubends.

CROSSWORD
ANSWER

ubends

Searching in Crosswords ...

The answer UBENDS has 2 possible clue(s) in existing crosswords.

Searching in Word Games ...

The word UBENDS is NOT valid in any word game. (Sorry, you cannot play UBENDS in Scrabble, Words With Friends etc)

Searching in Dictionaries ...

Definitions of ubends in various dictionaries:

No definitions found

Word Research / Anagrams and more ...

Keep reading for additional results and analysis below.

Possible Crossword Clues
Traps for plumber repairing sunbed
Fittings under the sink

Last Seen in these Crosswords & Puzzles
Aug 29 2019 New York Times
Mar 9 2017 The Guardian - Cryptic crossword

Ubends might refer to
In plumbing, a trap is a device shaped with a bending pipe path to retain fluid to prevent sewer gases from entering buildings while allowing waste materials to pass through. In oil refineries, traps are used to prevent hydrocarbons and other dangerous gases and chemical fumes from escaping through drains. * In domestic applications, traps are typically U, S, Q, or J-shaped pipe located below or within a plumbing fixture. An S-shaped trap is also known as an S-bend. It was invented by Alexander Cumming in 1775 but became known as the U-bend following the introduction of the U-shaped trap by Thomas Crapper in 1880. The U-bend could not jam, so, unlike the S-bend, it did not need an overflow. The most common of these traps is referred to as a P-trap. It is the addition of a 90 degree fitting on the outlet side of a U-bend, thereby creating a P-like shape (oriented horizontally). It is also referred to as a sink trap because it is installed under most sinks. * Because of its shape, the trap retains some water after the fixture's use. This water creates an air seal that prevents sewer gas from passing from the drain pipes back into the building. Essentially all plumbing fixtures including sinks, bathtubs, and showers must be equipped with either an internal or external trap. Toilets almost always have an internal trap. * Because it is a localized low-point in the plumbing, sink traps also tend to capture dense objects (such as jewelry or coins) inadvertently dropped down the sink. Traps also tend to collect hair, sand, food waste and other debris and limit the size of objects that enter the plumbing system, thereby catching oversized objects. For all of these reasons, most traps may be disassembled for cleaning or provide a cleanout feature. * Where a volume of water may be rapidly discharged through the trap, a standpipe may be required to minimize impact to other nearby traps.

Ubends might refer to

In plumbing, a trap is a device shaped with a bending pipe path to retain fluid to prevent sewer gases from entering buildings while allowing waste materials to pass through. In oil refineries, traps are used to prevent hydrocarbons and other dangerous gases and chemical fumes from escaping through drains.
* In domestic applications, traps are typically U, S, Q, or J-shaped pipe located below or within a plumbing fixture. An S-shaped trap is also known as an S-bend. It was invented by Alexander Cumming in 1775 but became known as the U-bend following the introduction of the U-shaped trap by Thomas Crapper in 1880. The U-bend could not jam, so, unlike the S-bend, it did not need an overflow. The most common of these traps is referred to as a P-trap. It is the addition of a 90 degree fitting on the outlet side of a U-bend, thereby creating a P-like shape (oriented horizontally). It is also referred to as a sink trap because it is installed under most sinks.
* Because of its shape, the trap retains some water after the fixture's use. This water creates an air seal that prevents sewer gas from passing from the drain pipes back into the building. Essentially all plumbing fixtures including sinks, bathtubs, and showers must be equipped with either an internal or external trap. Toilets almost always have an internal trap.
* Because it is a localized low-point in the plumbing, sink traps also tend to capture dense objects (such as jewelry or coins) inadvertently dropped down the sink. Traps also tend to collect hair, sand, food waste and other debris and limit the size of objects that enter the plumbing system, thereby catching oversized objects. For all of these reasons, most traps may be disassembled for cleaning or provide a cleanout feature.
* Where a volume of water may be rapidly discharged through the trap, a standpipe may be required to minimize impact to other nearby traps.

Anagrammer Crossword Solver is a powerful crossword puzzle resource site. We maintain millions of regularly updated crossword solutions, clues and answers of almost every popular crossword puzzle and word game out there. We encourage you to bookmark our puzzle solver as well as the other word solvers throughout our site. Explore deeper into our site and you will find many educational tools, flash cards and plenty more resources that will make you a much better player. This page shows you that Traps for plumber repairing sunbed is a possible clue for ubends. You can also see that this clue and answer has appeared in these newspapers and magazines: August 29 2019 New York Times, March 9 2017 The Guardian - Cryptic crossword . Ubends: In plumbing, a trap is a device shaped with a bending pipe path to retain fluid to prevent sewer gas...