Crossword Solver > found answer > REKEYS

Welcome to Anagrammer Crossword Genius! Keep reading below to see if rekeys is an answer to any crossword puzzle or word game (Scrabble, Words With Friends etc). Scroll down to see all the info we have compiled on rekeys.

CROSSWORD
ANSWER

rekeys

Searching in Crosswords ...

The answer REKEYS has 4 possible clue(s) in existing crosswords.

Searching in Word Games ...

The word REKEYS is VALID in some board games. Check REKEYS in word games in Scrabble, Words With Friends, see scores, anagrams etc.

Searching in Dictionaries ...

Definitions of rekeys in various dictionaries:

verb - to provide with a key (a device used to turn the bolt in a lock)

Word Research / Anagrams and more ...

Keep reading for additional results and analysis below.

Possible Crossword Clues
Confirms, as a password, perhaps
Types in again
Enters again, as data

Last Seen in these Crosswords & Puzzles
Aug 13 2018 Wall Street Journal
Dec 16 2016 USA Today
Mar 21 2012 Newsday.com
Oct 20 2001 New York Times

Possible Dictionary Clues
Third-person singular simple present indicative form of rekey.
enter (text or other data) again using a keyboard.

Rekeys might refer to
Rekeying a lock is replacing the old lock pins with new lock pins. Locks are usually re keyed to build master-key systems, make a set of locks share a common key, or to eliminate compromised keys. Sometimes worn pins are replaced with new pins if the old pins become too short to reach the shear-line. The shear-line is the thin line shared by the plug and its cylindrical housing. If a pin sits flush with the circumference of the plug it will allow lock rotation. Lock cylinders use different length pins in different combinations to create relatively unique key bitting. Most keys have 5 cuts from bow to tip. If a key has 5 cuts, the lock has 5 pins. Different brand locks each vary in many small ways, this is most true when servicing them. Many manufacturers offer product specific manuals. Information disclosed in manufacturer manuals is often otherwise difficult to find, as is locksmith material in general. * Pins are manufactured in .003" increments and .005" increments, pin kits contain an array of pins organized by length. Lock manufacturers each use specific depth and spacing allowing organized master-key systems to be complex, large, and manageable. A standard pin kit offers the exact size variety needed. Using manufacturer depths permits easy keying, but often you must deviate slightly for optimum accuracy. Pin kits provide master- wafers, top- pins, and springs for a thorough cylinder rebuild. Replace any worn parts, rekey, lubricate, and reassemble. Check to see that the keys work well, check remaining customer keys if any and reinstall. * To rekey a lock you have to first remove the lock cylinder from any housing it rests in. The lock cylinder must be disassembled, and the plug removed. Use a plug follower to avoid dropping master-wafers, top pins and springs. The plug has cylindrical chambers spaced according to manufacturer specifications. Pins are contained in these chambers where they are pushed down by springs or raised by a key. Each cut sits under a chamber of its own, each pin sits on a cut of its own. Place the correct pins in each chamber, bringing the top of each new pin flush with the shear-line. Check the upper chambers using a master-follower for old unused master wafers and remove any. If any springs are noticeably weak or the lock was especially dirty replace the springs. If the old pins are rounded from use or otherwise show excessive wear replace springs. Reinsert the plug taking care not to drop top pins into any unused chamber. Test key, make slight adjustments if needed and reassemble. * Rekeying was first invented in 1836 by Solomon Andrews, a New Jersey locksmith. His lock had adjustable tumblers and keys, allowing the owner to rekey it at any time. Later in the 1850s, inventors Andrews and Newell patented removable tumblers which could be taken apart and scrambled. The keys had bits that were interchangeable, matching varying tumbler configurations. This arrangement later became the basis for combination locks.

Rekeys might refer to

Rekeying a lock is replacing the old lock pins with new lock pins. Locks are usually re keyed to build master-key systems, make a set of locks share a common key, or to eliminate compromised keys. Sometimes worn pins are replaced with new pins if the old pins become too short to reach the shear-line. The shear-line is the thin line shared by the plug and its cylindrical housing. If a pin sits flush with the circumference of the plug it will allow lock rotation. Lock cylinders use different length pins in different combinations to create relatively unique key bitting. Most keys have 5 cuts from bow to tip. If a key has 5 cuts, the lock has 5 pins. Different brand locks each vary in many small ways, this is most true when servicing them. Many manufacturers offer product specific manuals. Information disclosed in manufacturer manuals is often otherwise difficult to find, as is locksmith material in general.
* Pins are manufactured in .003" increments and .005" increments, pin kits contain an array of pins organized by length. Lock manufacturers each use specific depth and spacing allowing organized master-key systems to be complex, large, and manageable. A standard pin kit offers the exact size variety needed. Using manufacturer depths permits easy keying, but often you must deviate slightly for optimum accuracy. Pin kits provide master- wafers, top- pins, and springs for a thorough cylinder rebuild. Replace any worn parts, rekey, lubricate, and reassemble. Check to see that the keys work well, check remaining customer keys if any and reinstall.
* To rekey a lock you have to first remove the lock cylinder from any housing it rests in. The lock cylinder must be disassembled, and the plug removed. Use a plug follower to avoid dropping master-wafers, top pins and springs. The plug has cylindrical chambers spaced according to manufacturer specifications. Pins are contained in these chambers where they are pushed down by springs or raised by a key. Each cut sits under a chamber of its own, each pin sits on a cut of its own. Place the correct pins in each chamber, bringing the top of each new pin flush with the shear-line. Check the upper chambers using a master-follower for old unused master wafers and remove any. If any springs are noticeably weak or the lock was especially dirty replace the springs. If the old pins are rounded from use or otherwise show excessive wear replace springs. Reinsert the plug taking care not to drop top pins into any unused chamber. Test key, make slight adjustments if needed and reassemble.
* Rekeying was first invented in 1836 by Solomon Andrews, a New Jersey locksmith. His lock had adjustable tumblers and keys, allowing the owner to rekey it at any time. Later in the 1850s, inventors Andrews and Newell patented removable tumblers which could be taken apart and scrambled. The keys had bits that were interchangeable, matching varying tumbler configurations. This arrangement later became the basis for combination locks.

Anagrammer Crossword Solver is a powerful crossword puzzle resource site. We maintain millions of regularly updated crossword solutions, clues and answers of almost every popular crossword puzzle and word game out there. We encourage you to bookmark our puzzle solver as well as the other word solvers throughout our site. Explore deeper into our site and you will find many educational tools, flash cards and plenty more resources that will make you a much better player. This page shows you that Confirms, as a password, perhaps is a possible clue for rekeys. You can also see that this clue and answer has appeared in these newspapers and magazines: August 13 2018 Wall Street Journal, December 16 2016 USA Today, March 21 2012 Newsday.com and more. Rekeys: Rekeying a lock is replacing the old lock pins with new lock pins. Locks are usually re keyed to bui...